Printing tear sheetClick here to close this tab and return to where you were.
Celeste Dreamcatcher Glass Tile
This stunning mosaic is created to look like stained glass. With a mixture of clear, iridescent, light blue and yellow-gold glass this tile will give a luminescent quality to any bathroom, kitchen or pool installation. Add a pop to any room with these beautiful, versatile tiles.
- Chip Size
- Sheet Size
- 12 3/4" x 12 3/4"
- 1.13 Sq. Ft.
- Mix of Iridescent, Clear, Light Blue + Yellow-Green
- Iridescent Polished
- 6 mm
Shaken or Stirred?
1-1/2 oz Vodka
1-1/2 oz Kahlua
Pour Kahlua into an iced old fashioned glass. Add vodka slowly to create a float. Fill with soda water, but don't mix. Serve with a straw.
Browse 7 questions Browse 7 questions and 47 answersWhy did you choose this?TileBar StoreI was looking for a glass tile that had blue, green and yellow blend, this was perfectMarilyn F on Jan 6, 2017can this be used for a shower floor?BEST ANSWER: I used it on a shower floor and have had no problems at all with it. I used the Bostik Dimension grout and it has a hardner in it that makes it almost indestructible. Ive dropped razors, shampoo, etc. Not problems at all.Can this be used for a shower ceiling? Would anything special need to be done in the installation?BEST ANSWER: My installation of this tile was a first, I used it for a table top on a coffee table. It is beautiful tile, but found removing the clear film difficult even though I followed the directions exactly. I placed a 1/4 inch backer board on the table top and used glass tile mortar which was very adhesive, the table is beautiful but I would think twice about using tile with a clear removal film. As far as using for a shower ceiling, I would call a professional tile installer.The sample tile was on a thin plastic backing is the actual tile on a mesh backing?BEST ANSWER: Tile Samples are usually cut from actual product so I would say yes. I can't recall exactly but I do recall it not being the same as other accent tile sheets I have purchased. We did install this in a shower as accent and around a tub deck. It does look nice and there were no issues from the installation regarding the material.what is the size of a sheet of Celeste Summery Bloom tile ?BEST ANSWER: Click on "Specs" on the page showing the tile and it's listed right there.Did this tile come on a single 12x12 mesh sheet or do you install them one tiny tile at a time?BEST ANSWER: 12 x 12 sheets. I had a highly-skilled tiler install my backsplash who had a special glass cutting tool. Cutting the little squares should be avoided wherever possible because the tiny glass squares shatter easily and that becomes expensive. The finished look is gorgeous.do you have an edge tile or treatment
that you would recommend for a kitchen back splash installation?BEST ANSWER: I used that tile in a different color around my fireplace. I did use an edge that was a small silver bar, flat on bottom and rounded on the corners in my kitchen so they tile didn;t meet the edge of the wall and leave a rough edge. Hope this helps. I got the silver edging at Lowes, but Tile Bar may have soothing like it for that purpose.
IMPORTANT INFORMATION REGARDING INSTALLATION for the Celeste Series
The Celeste Series is now produced as a face mounted mosaic. Instead of a mesh mounted sheet you will received a sheet with a plastic film holding the tiles in place. The purpose of this new faced mounted version is because it is ideal for mosaics often installed in submerged areas such as pools, showers, bathtubs etc. The plastic film is to be removed only once the sheet has been installed and the thin set has been given the adequate time to cure. We have tested several types of thinset and recommend the following:
Acceptable Thin-Sets • LATICRETE: 254 Platinum
Movement joints are essential for the success of most tile installations. Install movement provisions according to the “2011 TCA Handbook For Ceramic, Glass and Stone Tile Installation” method EJ171-11. A flexible sealant, recommended for submerged applications, is required between the tile and all restraining abutments (i.e. the decking or coping), at all inside corners and directly over any joints in the concrete tank. In-field movement joints are required every 8’ on center in exterior applications or 20’ on center in interior applications. An architect or design professional should be consulted when specifying the exact number and location of each movement joint. There are a wide variety of flexible sealants available for use in tile installations. Each sealant product will vary in type, application and performance; consult the sealant manufacturer for specific recommendations and imitations.
To initiate the bond coat, use the flat side of a trowel and firmly apply thin-set to the substrate
To establish the proper depth of the setting bed, use a 3/16” x 1/4” v-notch trowel to apply additional thin-set and comb full notches in one direction.
Use the flat side of the trowel to flatten the notches and achieve a smooth, consistent thin-set setting bed.
Apply mosaic sheets to the thin-set setting bed, tape side towards you, with light, even pressure. When joining sheets, be certain to adjust sheets so that grout lines are uniform. Periodically, check thinset for skinning (slight drying). If skinning occurs, remove thin-set and reapply
To achieve the flattest possible surface, lightly tap the sheets using light pressure with a grout float or a wooden beating block and a finish hammer. To unify sheet transitions, tap from one sheet to the next.
After the thinset has cured, peel the face mounting tape from the tile starting from the corner. Use an angled downward movement.