Printing tear sheetClick here to close this tab and return to where you were.
Celeste Autumn Fest Glass Tile
This stunning mosaic is created to look like stained glass. With a mixture of clear amber, brown, orange, red, & yellow-gold glass, this warm tile will give a luminescent quality to any bathroom, kitchen or pool installation. Add a crisp pop of Autumn to any room with these beautiful tiles that are versatile.
- Chip Size
- Sheet Size
- 12 3/4" x 12 3/4"
- 1.13 Sq. Ft.
- Brown, Amber, Orange, Red + Yellow-Gold
- 6 mm
Shaken or Stirred?
Traditionally prepared individually in an iced highball glass, this standard still packs a punch!
2 oz light rum
2 tsp simple syrup
Juice of 2 fresh limes
1 oz dark rum
Few drops of bitters
Pour light rum, syrup, and lime juice into a highball glass filled with crushed ice and stir until glass is frosted. Add dark rum. Fill with soda water and top with bitters. Garnish with fresh fruit and sugared mint sprigs.
Browse 2 questions Browse 2 questions and 8 answersWhy did you choose this?TileBar StoreThis was my favorite out of all the samples. The colors are rich without being overpowering. They will accent the wall above the shower surround.Susan G on Aug 17, 2016colors are great. They match my cabinet and flooring.Tobi W on Nov 19, 2015This was my favorite out of all the samples. The colors are rich without being overpowering. They will accent the wall above the shower surround.Susan G on Aug 17, 2016Blends in with all of the colors I have from the living room to the kitchen and I know have an open view from each room into the next.Melissa T on Sep 23, 2015Can this be used outside? Say under a pavilion?BEST ANSWER: Yes, this tile can be used outside.
IMPORTANT INFORMATION REGARDING INSTALLATION for the Celeste Series
The Celeste Series is now produced as a face mounted mosaic. Instead of a mesh mounted sheet you will received a sheet with a plastic film holding the tiles in place. The purpose of this new faced mounted version is because it is ideal for mosaics often installed in submerged areas such as pools, showers, bathtubs etc. The plastic film is to be removed only once the sheet has been installed and the thin set has been given the adequate time to cure. We have tested several types of thinset and recommend the following:
Acceptable Thin-Sets • LATICRETE: 254 Platinum
Movement joints are essential for the success of most tile installations. Install movement provisions according to the “2011 TCA Handbook For Ceramic, Glass and Stone Tile Installation” method EJ171-11. A flexible sealant, recommended for submerged applications, is required between the tile and all restraining abutments (i.e. the decking or coping), at all inside corners and directly over any joints in the concrete tank. In-field movement joints are required every 8’ on center in exterior applications or 20’ on center in interior applications. An architect or design professional should be consulted when specifying the exact number and location of each movement joint. There are a wide variety of flexible sealants available for use in tile installations. Each sealant product will vary in type, application and performance; consult the sealant manufacturer for specific recommendations and imitations.
To initiate the bond coat, use the flat side of a trowel and firmly apply thin-set to the substrate
To establish the proper depth of the setting bed, use a 3/16” x 1/4” v-notch trowel to apply additional thin-set and comb full notches in one direction.
Use the flat side of the trowel to flatten the notches and achieve a smooth, consistent thin-set setting bed.
Apply mosaic sheets to the thin-set setting bed, tape side towards you, with light, even pressure. When joining sheets, be certain to adjust sheets so that grout lines are uniform. Periodically, check thinset for skinning (slight drying). If skinning occurs, remove thin-set and reapply
To achieve the flattest possible surface, lightly tap the sheets using light pressure with a grout float or a wooden beating block and a finish hammer. To unify sheet transitions, tap from one sheet to the next.
After the thinset has cured, peel the face mounting tape from the tile starting from the corner. Use an angled downward movement.