Printing tear sheetClick here to close this tab and return to where you were.
Be original and your home will speak for itself. Resurrecting the sophisticated grace of old-school New York, Caprice juxtaposes clean White Thassos marble with glass accents that will seamlessly bring a touch of elegance and panache to your space. Create a dazzling backsplash with serious wow factor or go full-on luxe by incorporating Caprice as a lavish full feature wall installation. Life should be chic, glamorous and awe-inspiring, and so should your home.
- Sheet Size
- 11.25" x 11.25"
- 0.83 sq. ft.
- Marble (White Thassos & Glass)
- Residential Use
- Wall Only
- Commercial Use
- Wall only
Shaken or Stirred?
Caribbean Rum Punch
- - 1/2 oz. lime juice
- - 4 oz. orange juice
- - 4 oz. pineapple juice
- - 1 1/2 oz. dark rum
- - 1 1/2 oz. light rum
- - Splash of grenadine
Mix ingredients together in a cocktail shaker or blender. Pour over a cup half filled with ice. Sprinkle nutmeg on top and garnish with an orange slice & cherry.
Browse 2 questions Browse 2 questions and 3 answersCan this be used as an accent stripe for a shower?BEST ANSWER: Yes this tile is suitable for shower installations. Note that both mirror and marble can lose their polish and sheen over time if submerged in water, but mere contact with water is fine. Also note that marble should always be sealed well when used in wet areas.Can this tile be used as backsplash over stove?BEST ANSWER: Yes you can. That is exactly what I used it for and it looks beautiful! I've had it up for a few months and I've had no issues keeping it clean.
Hope that helps
These instructions are meant to be a guide for most installations, under normal conditions. Please follow best practice instructions found in the Tile Council of North America (TCNA) 09300 Handbook for specific installation types.
Due to the natural of the material no two pieces of natural stone are exactly alike. Natural stones are products of nature; therefore, variations in color, pattern, texture, and veining will occur. Verify all products before installation for any damage or defects such as chipped edges, broken pieces. No adjustment will be made after installation.
*Always use appropriate personal protective safety equipment when handling, drilling, cutting or grinding glass tile such as (but not limited to) eye, ear and hand protection.
Before you start tiling, make sure that whatever surface the tiles are being installed to will be strong and structurally sound. Cement board, concrete or drywall is best, as these surfaces can handle the moisture of the tiling process. Plywood should be avoided, since the wood will warp with the added moisture and it will also be less waterproof, even after tiling.
When setting tiles we recommend the use of polymer or latex modified thin set or medium bed mortar compliant with ANSI standard A118.4 and is recommended for use with marble tile.
3/16” or 1/4” square notch trowel should be used when installing our glass material and ridges should be smoothed down with the flat side of the trowel prior to fixing the tiles in the mortar bed.
Use a wet-saw with a new, continuous rim diamond blade specifically designed for cutting marble. Do not use “turbo” or other notched blades designed for use with porcelain or ceramic as the teeth can cause a coarse cut, resulting in a heavily chipped edge.
Cut edges and corners will be sharp. Always be sure to smooth the cut edges manually with 200-grit wet/dry sandpaper.
If possible, drill holes before installing tile. Drilling from both sides can ensure a cleaner finish if the hole will be visible after installation. Using a new diamond coring bit (for large holes) or spade bit (for small holes) with a diamond tip made for glass drilling will give the best results. Lubricating the bit and tile surface with a continuous spray of oil/water mix will prolong the life of bits and provide a better-finished edge. When possible, the use of a jig will ensure precise placement of holes to be drilled.
When drilling holes for anchoring bolts, plumbing or any other dissimilar material always ensure a minimum of 1/8” clearance around the item is provided to avoid cracking due to disparate expansion and contraction rates or stress transfer.
We recommend applying grout release prior to grouting, suitable for the respective stone and interior or exterior use, to the tile to facilitate cleaning and for protection against staining from contrasting color grouts. Grout joints should be packed full and free of all voids and pits. Excess grout should be cleaned from the stone surface as the work progresses, before the grout hardens. Do not use acids to clean off excess grout. Prior to grouting, test an area to make sure the stone surface will not scratch.
After the stone is installed, and grouted, seal the stone with an appropriate high quality breathable stone sealer, to minimize water absorption, efflorescence, and potential staining. If necessary, a color enhancer may be applied to bring out the true color of the stone at any time after grouting. Follow sealer manufacturer’s installation instructions. Reseal tile when the stone gets darker or as needed.
CARE AND MAINTENANCE
For normal care and maintenance of stone tiles, clean stone surfaces with a few drops of neutral cleaner, stone soap, or a mild liquid dishwashing detergent and warm water. Use a clean soft cloth for best results. Too much cleaner or soap may leave a film and cause streaks. Do not use products that contain lemon, vinegar, or other acids on marble or limestone. Rinse the surface thoroughly after washing with the soap solution and dry with a soft cloth. Do not use any abrasive cleaners.