Printing tear sheetClick here to close this tab and return to where you were.
Breeze Stylus Carrara Ice Pattern Glass Tiles
Give your kitchen that stylish and frosty modern look with our Breeze Stylus Carrara Ice tile. This gorgeous white Carrara blend is ideal not just for backsplash, but also for use as an island or floor accent! Whether using this stunning tile as a back splash wall, or as an accent piece, the white Carrara and white glass will give your room a classic and contemporary setting. Add a small touch of "wow" to any room.
- Chip Size
- 1/8" x Random
- Sheet Size
- White Carrera + Super White
- White Carrara + Glass
- Frosted + Polished
Shaken or Stirred?
In Pennsylvania the tax on wine and spirits is called the Johnstown Flood tax because it was imposed in 1936 to raise funds to help the city of Johnstown rebuild and recover from a devastating flood that year. The city of Johnstown quickly rebuilt and recovered but the tax still continues. It currently costs the taxpayers of the state over $160,000,000.00 each year.
Browse 4 questions Browse 4 questions and 12 answersWhy did you choose this?TileBar StoreThe tile color and pattern complemented my granite countertops. It softened the look of the countertops.Julie L on Nov 8, 2016This tile just drew me in and kept pulling me back to look at while it does not overwhelm the granite counter top but complements it.Dale T on Feb 13, 2015The tile color and pattern complemented my granite countertops. It softened the look of the countertops.Julie L on Nov 8, 2016Just rnough sparkle, without being too shiney, liked the detail. Tiler didnt seem to take an attitude about the small pieces, its very elegant, plan to run vertical, not horizontalT O on Sep 17, 2015Just rnough sparkle, without being too shiney, liked the detail. Tiler didnt seem to take an attitude about the small pieces, its very elegant, plan to run vertical, not horizontalT O on Sep 17, 2015How do you recommend finishing the edges of the tiles where they don't butt up to trim in our kitchen? Can the tiles be cut evenly and just end (caulk?)? Do I have to put a vertical trim piece down the edge?BEST ANSWER: The pieces are random lengths and there are lots of glass bars. Since the individual bars are thin, the ends do not cut evenly unless you cut with hand tools and some practice or skill. With a small tile saw the cut ends will come out sharp and rough. You can turn the uncut ends towards the edge and use grout to fill gaps between the polished end and the cut end. Make sure to get extra tile if the pieces are not the right length.I recently bought this, and am waiting for it to be installed. My question is "where is this manufactured?BEST ANSWER: This tile is manufactured in China.placing the tile horizontally is the size 11 inches horzonially by 13 inches vertically?
Tile must be installed over a suitable substrate to insure a proper installation. Tile should be installed over a clean, sound, and flat surface, free of contaminates including curing compounds. Substrate should be free of cracks. If used in a wet area you must waterproof. Tile must be sealed.INSTALLATION
- To avoid affecting the color of the tile, White modified thin-set such as Bostik Glass Mate is highly is recommended for all installations.
- Apply as much adhesive as can be covered within 10-15 minutes.
- Grout joint should be a minimum of 1/16” and not butt set.
- The trowel size you can use is a 9" Trowel - 1/16" square notch.
- Use Non-Sanded grout
- Grout joints should be packed full and free of voids and pits.
- Clean excess grout as the work progresses before it has hardens completely.
- Acids should never be used for cleaning grout haze.
- Use a damp sponge for the final cleaning and to smooth out the grout joints.
- It is recommended to use grout release, then grout the tile, then use a sealant to the tile such as our MP90
- Highly recommended to purchase the Glass & Stone Installation/Maintenance Kit - http://www.TileBar.com/collection/tiling-supplies/glass-stone-tile-maintenance-package.html
The recommended cutting method is to use a wet saw with a diamond blade that is specifically for cutting glass. Edges can be sanded smooth after cutting.